This thread is for any interesting Avenger parts you have seen on Trademe or similar sites.
I'll start with this turbo kit for an Avenger.
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Chrysler/Engines/auction-346162052.htm
Twin Sturmberg carbs and manifold for an Avenger
http://www.trademe.co.nz/a.aspx?id=347417471
Cam
http://www.trademe.co.nz/Browse/Listing.aspx?id=345496984
I won
thanks to another member for the specs and heads-up
Quote from: Avengacheck this out
http://www.trademe.co.nz/a.aspx?id=345496984
It is a Kelford Cams F29 grind. From what I have read it is low end race spec. I don't know if your head would be big enough for it and it is more suited for dual webers/dellortos but could be worth a shot for $100. I use a custom made F63-7 Kelford cam in my road car.
These are some F29 specs I pulled off the net, they are from a toyota cam but I am pretty sure the F29 profile is the same over all car makes.
F29
Cam Lift 0.290"in 0.300ex
Valve Lift Net 0.419"in 0.432ex
Duration @ 0.050 236 in 248ex
CEnterline @ peak lift 105 105
lobe seperation 105
Cam time @ 0.050" Camlift
Intake open 13btdc
intake clases 43abdc
Exhaust Opens 49bbdc
exhasut close 19 atdc
Valve time @ 0.015" Camlift
Intake open 37btdc
intake clases 67abdc
Exhaust Opens 72bbdc
exhasut close 42atdc
Quote from: JoKer on January 16, 2011, 09:14:47 PM
Cam
http://www.trademe.co.nz/Browse/Listing.aspx?id=345496984
I won
thanks to another member for the specs and heads-up
Awesome mate. be keen to see how it goes it your Avenger. Get that installed and those Solex carbs going and you should see quite a nice gain in performance.
Keep us up to date on how it goes.
Looks like a good source of spare parts.
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Other-accessories/auction-348892845.htm (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Other-accessories/auction-348892845.htm)
Quote from: http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Other-accessories/auction-348892845.htm
Huge range of Hillman parts
Lots of parts stripped from several 1974 Hillman Avengers.
Just comment on the part you are looking for and i'll let you know if it's here, the condition it's in and a price. I'll upload a photo if needed
Avenger front black high back seats
The guy is sending me some photo's but these are pretty hard to come by. I have high back buckets in my 1975 Hillman Avenger and they are much better than the standard low back seats. being black they might be out of a TC but I can tell when I see the pictures.
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Chrysler/Interior/auction-348936394.htm
They do look like Avenger TC seats. Pretty rare. Here is a picture.
(http://images.trademe.co.nz/photoserver/89/157447289_full.jpg)
nice shape to those seats they must have only been available here were they? never saw them before
english rally car for sale good spec listed on asoc as well
http://www.pistonheads.com/sales/2405883.htm
Yeah the TC (stands for Twin Carb) was only available in NZ in 1971 and 1972, it featured a full black interior with those seats. In 1973 the TC was replaced with the Avenger Alpine which was a 1500 Twin Carb similar to the UK GLS, it 1974 the went to 1600 Twin Carb.
The engine from my 1975 Hillman Avenger is a 1500 from a 1973 Avenger Alpine.
They were not all black, I had a 72 1500 TC with a beige interior...
Damn man I should never trust Wikipedia
Quote from: http://en.wikipedia.org/wiki/Hillman_Avenger
In 1971 Todd's added a unique-to-NZ, sporty, 1.5-litre twin-carburettor 'TC' model with all-black interior trim, dashtop rev counter, side striping, high-back 'tombstone' front seats, special bright paint colours and new wheel trims, among other detail changes. This was loosely based on the UK GT but lacked that car's 'Rostyle' wheels, using NZ-made, look-alike pressed aluminium wheel trims instead.
I have only seen a couple of TC's and they have been black interior but a lot of the info on the net about NZ Avengers is a bit sketchy so that is why I made this site so we can hear from people who actually owned the cars.
Thanks for the correction and thanks for proving wikipedia wrong.
hillman avenger engine
Quote from: http://www.trademe.co.nz/a.aspx?id=350116758here i have my standard 1974 hillman avenger engine its a 1.5l was running when removed from car comes with 4 speed gearbox clutch and all the rest .
engine done 115000kms
will come with twin carbs and manifold if buy now is used
buy now $450 cash ono
Seems a bit pricey since I brought my 1500 Avenger Alpine engine for $100. Maybe I should sell my old 1500 with the downdraft weber if I can get that sort of money.
Quote from: avenga on January 27, 2011, 08:49:35 AM
Seems a bit pricey since I brought my 1500 Avenger Alpine engine for $100. Maybe I should sell my old 1500 with the downdraft weber if I can get that sort of money.
nah sell it to me for $100...haha. have tracked down a potential engine down here in wellington. am waiting for more info on it but apparently its grumpy as hell. is in bits though lol
Sweet, The grumpy engine and new wheels should really transform your Avenger. You will be giving my Avenger a run for its money. You going dual carbs? dellortos? Webers? Strumburgs?
ill see what the engine specs are first. the guy is meant to be letting me know today. its in bits and needs a crank grind, but by the sounds of it its a pretty nice motor. should be able to get it pretty cheap as well. time will soon tell
Hillman Avenger Carpets "BUY NZ MADE"
Quote from: http://www.trademe.co.nz/a.aspx?id=350642784Replacement carpet sets for Hillman Avengers.
Sample photo only.
We also have Hunter - Hawke - Super Snipe - Imp - Super Minx - Rapier - Humber 80 - Humber 90 - Subeam Alpine etc etc
All available in 8 colours including Black.
All carpets in genuine Tufted Cut pile carpet.
We have matching Car Mats & Bootmats.
Full range of insulations for Engine Bay - Sound Deadning - Underfelt and Dynamat available
I got my carpets for my 1975 Avenger from these guys. They are made by Autodec in Manukau, Auckland. You can see photos of the installation under my "Avenga's 1975 Avenger (http://www.avenger.co.nz/forum/index.php?topic=13.0)" thread.
I installed them myself over easter weekend last year, they were a really good company to deal with, I rung and ordered them on the Monday before easter and he said he would get his guys to start making the carpets straight away so I could have it to install over the long weekend. They arrived at my doorstep on Wednesday morning, less than 2 days later. Can't ask for faster than that.
I chose to go for a dark chocolate brown, It looks much darker than in my photos. I had a few fitment issues with the mould for the transmission tunnel being too wide but I trimmed that and hid the cuts under the centre consoles. I also have to cut the carpets to get it to fit around the pedal box and heater but that was easily done.
Another Hillman Avenger parts car.
hillman avenger 1977 parts
Quote from: http://www.trademe.co.nz/a.aspx?id=350829816almost a whole car of parts the dif is seazed motor is in unknown condition, just ask and i will see if i have it and start a auction.
Please dont bid on this auction
and im after a road worthy avenger if anyone is trying to sell one
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-350852502.htm
13" x 10" :P with slicks! mate is selling them
I have to see if they will fit... just once...
Man those are awesome. You would have to put some serious flared arches on the get those bad boys to fit.
I had to roll the guards on my race car to get my 205/60/R13 tyres on 13x7 Hotwires to fit.
haha yeh there is no way those will fit. my new rims are only 6" and maybe half that dish and they are inline with the guards
My 13x6" tridents with 185/70/R13 Goodyear rubber fits nicely under the stock guards, much bigger than that I think you will have to start modifying the wheel arches.
at the end of the day its all about offset really
True, I guess your offset is a lot different on your mags. I have never checked to see how much room you have on the inside on the arch.
I had a look at some of my old photos and here is one where you can see the inside clearance on my race car with its 205s, there is a bit of room but not enough for those 10" rims. Mini-tubbed Avenger anyone?
(http://i871.photobucket.com/albums/ab274/avenga76/1980%20Avenger/avenger023.jpg)
I saw this Avenger Wagon listed, Pretty rough shape, probably only good for a parts car unless someone is looking for a real project.
Chrysler / Hillman Avenger 1980
Quote from: http://www.trademe.co.nz/a.aspx?id=351898915Must go $1 no reserve
Bought this vehicle around 6 years ago, and has been a work in progress type ever since. Has had a WOF a couple of times but now the rego has lapsed so really only suitable as a donor car.
Has been professionally lowered with compressed springs and shortened shock absorbers - believe they can go into a sedan also.
The motor has a worked cam and twin carbs although one of the carbs (it may not go at the moment - Its been a year since I have visited the car...)
Also have a wildcat downdraft manifold for it (can seperate)
Heaps of spares inside the car though I think half of them are for an r31 skyline...
Nice Sportsline(?again cant remember) wood steering wheel - probably worth more than the car itself
gearbox and diff are in good nick from memory.
Probably other things but again been a year so I am a bit hazzy.
I will be down in christchurch on thursday 10th feb if anyone wants to view it will have to arrange for a time then, and will need the payment for the car and it to be picked up before 10am sunday 13th feb (as I am leaving chch again)
(http://images.trademe.co.nz/photoserver/65/158738665_full.jpg)
(http://images.trademe.co.nz/photoserver/5/158738705_full.jpg)
(http://images.trademe.co.nz/photoserver/13/158738713_full.jpg)
Hillman Avenger 1600 cc motor and autogearbox
Quote from: http://www.trademe.co.nz/a.aspx?id=352127198This is a little sweety was running up to a teminal crash when the car it was in was written off was going to put it in my vouge but to many other jobs to do just want to clear from garage
(http://images.trademe.co.nz/photoserver/50/158850350_full.jpg)
want!
ill buy and you can buy the bgox of me and use bellhousing?
Yeah I would be keen on the bell housing so I can do my 5 speed conversion.
We should offer the auto gearbox to "Oldschool" as a spare for his son's automatic Avenger.
shit, am so keen now. hmmmmm I'm away fro the next 10 days, will see if he will hold onto it. also asked what it ran like, how long its been sitting etc so will see what they say.
Sweet. I'm keen so just let me know what you work out.
i could keep the bellhousing, but realistically, theres more chance of you getting it done before I do haha
And that way I can be the guinea pig and let you know all the things to watch out for.
I have added a couple of Sierra gearboxes to my watchlist so let me know how you get on.
haha yeh that also
Chrysler Avenger 1.3 GL 1980 for sale on Trademe. Starting bid $900 no reserve.
Looks tidy and seems a steal at that price. I will be watching this auction with much interest. Hopefully a forum member gets it.
Quote from: http://www.trademe.co.nz/a.aspx?id=352460974Chrysler Avenger 1.3 GL 1980
Two lady owners (plus dealer).
My wife has owned this car since 1990 and the 141,156km travelled is genuine.
Has been regularly serviced.
Electronic Ignition
New Front tyres 3,000km ago
New diff. Pinion Seal at 138,820km.
New front Wheel Bearings at 139,919km.
6-July-2010 - New SLA battery ($160.00)
20-Dec-2010 - New Fuel Pump (Wasnt needed though)
11-Jan-2011 - New Diaphragm in Carburettor
New Rear Muffler
Compression Check:- All between 160psi/11.3kg and 175psi/12.3kg.
(with-in manufacturers specifications)
Notes:- The trip meter is not working.
There is a small amount of play in the right end bush of the steering rack, but OK for WOF.
Some cracks in the dash board plastic - see photos.
Small dents in L. Rear door near hinge and rear bumper. See photos.
All doors open and shut nicely.
(http://images.trademe.co.nz/photoserver/59/159006459_full.jpg)
(http://images.trademe.co.nz/photoserver/35/159006335_full.jpg)
(http://images.trademe.co.nz/photoserver/2/159007002_full.jpg)
(http://images.trademe.co.nz/photoserver/96/159006896_full.jpg)
My baby! I must have it. I want to be a part of the Avenger family!
It looks like all the 1980 Chrysler Avengers are coming out of the woodwork lately.
Another 1980 Chrysler Avenger Estate.
Quote from: http://www.trademe.co.nz/a.aspx?id=352786813This car has been the most trustworthy car I have ever owned. It starts every time and is very quick for a 1600cc. There is a bit of paint missing on the back boot lid from having a bike on the back. It has been around the clock a few times so am unsure of the correct mileage as the odometer doesn't go up that high.
Features include a CD player / radio and towbar.
Would make a perfect first car or project as it gets plenty of attention. A great classic!
(http://images.trademe.co.nz/photoserver/31/159204731_full.jpg)
(http://images.trademe.co.nz/photoserver/0/159204700_full.jpg)
(http://images.trademe.co.nz/photoserver/12/159204712_full.jpg)
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Nonalloy-wheels/auction-352067857.htm
6" rims
I found this on Sella, not sure if it counts but someone may be interested! :)
http://www.sella.co.nz/motoring/cars/chrysler/79sf6x/
(Feel free to move this post if it's in the wrong place)
rims :
(http://images.trademe.co.nz/photoserver/tq/54/149822054.jpg) (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-353650114.htm)
(http://images.trademe.co.nz/photoserver/tq/36/112674336.jpg) (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-353790167.htm)
(http://images.trademe.co.nz/photoserver/tq/48/158773248.jpg) (http://www.trademe.co.nz/Browse/Listing.aspx?id=353368871)
(http://images.trademe.co.nz/photoserver/tq/39/152909639.jpg) (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-354354879.htm)
I like that last set. the black paint looks really good. Wish my Charger rims were like that when I brought them. They look really good now that I have painted 2 of them, 2 more to go.
tempted to get for some slicks :P (I have a whole 3 scrounged up for fun times
Found this guy in the USA selling lots of NOS Avenger parts....US$7.20 for a water pump is ok!
http://stores.ebay.com/Vintage-Imports-Inc/Hillman-/_i.html?rt=nc&_nkw=avenger&_fsub=9678524&_sid=7898167&_trksid=p4634.c0.m14.l1581&_pgn=1
(http://images.trademe.co.nz/photoserver/2/159007002_full.jpg)
I now know where my dash is from! i have this in my rally car....
It's the same kind of dash as I have in my race car also.
(http://i871.photobucket.com/albums/ab274/avenga76/1980%20Avenger/P2210015.jpg)
Does using a standard steering wheel in your race car work out better than a sports wheel Richard?
I'd like to get a sports wheel if anyone has a spare?
The standard wheel was way too big for racing so I switched to this wheel here. Much better for racing.
(http://i871.photobucket.com/albums/ab274/avenga76/1980%20Avenger/avenger_puke008.jpg)
I do have a spare old Wildcat sports steering wheel. I can send you some photos, it comes with an Avenger boss kit. It invoked this response from another member "god thats ugly haha" so I suggest looking at the pictures before you say you want it. If you are interested I will email you the pictures.
now thats better!
Those Hillman Avenger TC seats are back on Trademe. I guess the last deal fall through.
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Chrysler/Interior/auction-355404587.htm
(http://images.trademe.co.nz/photoserver/28/160455928_full.jpg)
I was tempted, but they'd cost about $1000 to recover...have to draw the line somewhere....lol
I went around to see this 1974 hillman avenger
(http://www.trademe.co.nz/a.aspx?id=356466147)
Body looks pretty tidy, I could see any rust so it could be a good base for a project or a reshell. It has a standard 1500 engine with dual strumberg carbs. Engine doesn't go because he is missing the linkages etc for the twin carb setup, he said the engine worked before he put the dual carbs on.
Here are some pictures.
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030854.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030855.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030856.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030859.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030860.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030861.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030862.jpg)
(http://i871.photobucket.com/albums/ab274/avenga76/Avengers/P1030863.jpg)
What did you think of the car? Do you think it would be a easish project? Does he still have the single carb so it can be driven again?
Cheers
From what I saw of the body it is good, I couldn't see any rust but it has had a matte black paintjob done on it so I don't know if it is hiding any bog under the paint or not. The owner told me there wasn't any rust or bog under the paint.
He said he still has all the single carb gear and it was running well before he put the dual carbs on but best confirm with him before buying it just to make sure he has everything you need.
Inside is a bit rough, tears on the seats and the dash is pretty cracked up but what Avenger isn't now days. looks like it has been recarpeted with house carpets, could be wrong but that's the way they look.
It has a good set of tyres on it. The owner said it flew through it's last WOF. It still has a month or 2 of WOF left and the rego is on hold.
It had no battery or radiator fan, the owner said he was planning to put in an electric fan.
I think it is worth restoring Vs a parts car. The body looks solid and if you can negotiate a good price then it should be a good base for a project car but she does need some work.
Thanks Avenga
What would you say its worth?
My biggest problem is i live way down south so would cost abit to get it here but these things re quite hard to find bugger it. Espeacily down here at a reasonable price.
THanks Nic
Hard to say what it is worth. It depend how much you want it and how quickly the seller wants to get rid of it. 79avengerGL is selling his for $600 which I think is good for his Avenger. This one is very similar to 79avengerGL in that they both don't run at the moment and are both resprayed matte black. Both of them need work but they would probably both be worth restoring.
If 79avengerGL was worth $600 then I would guess this one would be worth a little bit more due to it being a 1500 instead of a 1300 and it does seem a bit more complete with all it's door cards and grilles.
He said offers so I would start the negotiation around the same price as 79avengerGL's $600 and see what price you can get it for. He indicated to me that he wanted $800-1000 for it. I think $1000 is way to high for a non-running project Avenger when you look at some of the other Avengers which have sold lately.
auto! avenger on trademe http://www.trademe.co.nz/Trade-Me-Motors/Cars/Chrysler/Avenger/auction-361385043.htm
That's in mint condition
That is mint, funny model tho, a Chrysler GLS with vinyl seats??must be late 78 an regod in 79 unless they askd for vinyl, I still want it
that is a clean one hope it goes to someone who appreciates it.cant be many left in that condition now.
I had a 78 - no way is that a 78?!?!
indicators in wrong place - unless that was changeover year?
(http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc3/30200_418203632455_768657455_5298156_3870906_n.jpg)
same seats thou
My cream one is a 78, as far as I know face lift models were late 77
Sure is a tidy Avenger. I had the same seats in my 1980 Avenger GL.
Interesting they call it "Apache Red". It is the same colour as my '80 was and it's paint code was AR, I always jokingly said it stood for "Avenger Red" but that must be it's true name.
I like what they have done with the front speakers. Sort of the same idea as mine. Dashboard looks really mint which is rare for a Chrysler.
Makes that '80 Scout brought look like a good deal at that price. It will be interesting to watch. I hope who ever buys it joins the forum because it is a pretty rare model now.
(http://images.trademe.co.nz/photoserver/tq/87/162227287.jpg) (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-360869657.htm)
(http://images.trademe.co.nz/photoserver/tq/11/158817611.jpg) (http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-362144964.htm)
I like those 4 spoke ones.
that auto avenger is mint
Diff ratio is taller too apparently in an Auto if you want to go faster - might be handy for track work
I use a wagon diff for that reason. It has a 4.11:1 ratio. heaps quicker off the line than a 3.89:1 or 3.70:1.
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Nonalloy-wheels/auction-361675045.htm
Rostyles x2 $20
I've got my 14" x 7" Globes for sale on TradeMe if anybody's interested?
http://www.trademe.co.nz/Browse/Listing.aspx?id=363596329&ed=true
Nice globes. My mate has them on his Torana wagon. They look awesome all painted and polished. Another one of my mates has globes on his Charger.
Check out these mint 13 x 6 Globes....what a steal at only $400 reserve!!!
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-364246902.htm
Wow, they do look nice.
Toyota powered Avenger race car.
Hillman Avenger in mint condition with complete toyota running gear. Motor is a 1ggte with single cast iron HKS manifold running a T3 garrett turbo larger injectors and aftermarket ecu with supra gearbox. Custom plenum with top mount intercooler which make very responsive on circuit as little lag with no piping.2 piece Wilwood disc and 4 pot calipers with yellow ebc pads in front and toyota hilux rear end with modified diff head.It has racetech seat and full camlock harness.Homoglated cage with Log book all stripped interior and lighted dr cards on front drs.
Full set of bridgestone slicks in new condition 195/65/15 and 15 by 7 roh rims.Complete adjustable suspension plus gas canisters in boot for damper adjustment also.
Has just been on dyno and pulled out 270 atw at 17 psi.
http://www.trademe.co.nz/Trade-Me-Motors/Specialist-cars/Competition-cars/auction-367871563.htm
(http://images.trademe.co.nz/photoserver/0/167085600_full.jpg)
That's so sick.. love guards like those. Do you know where i could get the chrome filler strip it has in it's windows?
avengerparts on here sells the chrome filler strip (im assuming you mean for the windscreens)
Dellorto DHLA40's plus manifold!! Get some proper carbs on your Avenger! pretty good buying at a buy now of $400. My manifold was $100 and my DHLA40's were $500.
Quote from: http://www.trademe.co.nz/a.aspx?id=368779026Inlet manipold is off a 1600 Chrysler Avenger Alpine. Carbs have new seal kit. Regulator is good. 4x filters as per photo.
(http://images.trademe.co.nz/photoserver/30/167480830_full.jpg)
ill stick with my dream of twin shiny SU's for now haha
Would be nice, but thirsty of course....lol
Wonder if anyone makes a single Dellorto Avenger manifold?
Saw one on an MG when we were in Hastings - looked great - probably went well too, without being too thirsty!
haha yes very thirsty. Also, its really not worth it unless you have work done elsewhere on the motor.
Yeah you really need to do heaps to an engine to get the dellortos to work but those manifolds are rare so if you were ever thinking about doing it then they would be good to have.
Well those carbs didn't last long. sold already.
yes you can get a fannymold for a single 40 or 45 here is one for sale on asoc in the uk for 350gb complete
(http://i267.photobucket.com/albums/ii293/dave74_2008/lynxavenger.jpg)
Lynx make some wierd manifolds.
Here is a single weber for a Valiant 225 sloper
(http://img89.imageshack.us/img89/3781/dsc00829.jpg)
They also made a dual SU manifold for the Valiant Hemi 6
really have to wonder how much og an imbalance there is between the amount of air/fuel getting into each cylinder. I suppose the suction create in the bores would essentially shift the same amount of air/fuel for each cylinder so it wouldnt really matter
Yeah that is a huge problem with that. 3,4 are really rich then 2,5 are good and 1,6 are lean.
This is a standard manifold for a hemi 6
(http://www.hemiperformance.com/store2/images/uploads/hemi%206%204bbl%20manifold.jpg)
This is what I run, it has longer middle runners to help
(http://www.valiantspares.com.au/images/Aussie%20speed%20pics%20009.jpg)
With a plenum pig to help airflow
(http://www.pentastarparts.com.au/sunshop/images/products/large_2972_plenum-pig.jpg)
(http://www.pentastarparts.com.au/sunshop/images/products/large_2972_plenum_pig_installed.jpg)
The slopers had more room so they had this to solve the problem completely
(http://elkoperformancesydney.com.au/media/catalog/product/cache/1/image/5e06319eda06f020e43594a9c230972d/a/s/as0024_640.jpg)
ah sweet cheers for that.
moral of the story however, is just run SU's at a maximum of 2 cylinders per carb. and if they are shiny then thats a bonus
WOW some of those manifolds are sick...that Elko one must have enormous throttle lag....lol
Check out this hemi side draught on a Charger for sale on TradeMe...cyls 1 and 6 would be lucky to get any fuel....haha
Quote from: hunted on April 15, 2011, 11:22:05 AM
ah sweet cheers for that.
moral of the story however, is just run SU's at a maximum of 2 cylinders per carb. and if they are shiny then thats a bonus
Or run Dellortos, nothing like having 1 carb per cylinder.
Quote from: oldschool on April 15, 2011, 12:02:29 PM
WOW some of those manifolds are sick...that Elko one must have enormous throttle lag....lol
Check out this hemi side draught on a Charger for sale on TradeMe...cyls 1 and 6 would be lucky to get any fuel....haha
Haha that is the worst carb setup I have seen on a Charger, wonder how it goes.
Yeah you would get heaps of throttle lag on that last one but you would get heaps more top end.
There was a factory option called the "Hyper-pak" which had long runners like that.
(http://i3.photobucket.com/albums/y79/slantvaliant/47_3.jpg)
(http://www.moparmagazine.com/assets/images/sept-oct_2009/heritage/hyper-pak_slant_six.jpg)
For the 265 hemi the performance model was the "six pack" triple 48mm webers
(http://hooniverse.com/wp-content/uploads/2010/09/six-pack.jpg)
Hello my name is Rodrigo, I'm from Argentina and I have a Dodge 1500.Es a car much like the Hillman Avenger would be like a distant cousin jeje.Estoy interested in getting a intake manifold like the picture to put a webber 40 / 40 to have better performance, please let me know if you know of any that the venta.Un hug from Argentina
Hi Rodrigo. Welcome to the forum. We are very interested in the dodge 1500's. What model 1500 do you have? does it have the 1800cc engine? we only got 1300/1600cc engines in New Zealand.
As for the manifold there is a single weber lynx manifold on Ebay UK at the moment
http://cgi.ebay.co.uk/Talbot-Avenger-Weber-Webber-Dellorto-manifold-/330553387252
(http://i.ebayimg.com/00/$(KGrHqF,!ikE2LhluV)mBNjM6wQ7nQ~~_12.JPG)
Or if you want dual weber then there is a dual monifold on Ebay also.
http://cgi.ebay.co.uk/Talbot-Avenger-Twin-Weber-Webber-Dellorto-manifold-/330552235517
(http://i.ebayimg.com/00/$(KGrHqQOKo0E0flOvQubBNc5ibb77w~~_12.JPG)
Ebay UK is probably the best place to look for performance parts as they are pretty hard to find in New Zealand. I had to get my dual weber manifold from Australia. Here is a picture of my engine bay. I run dual dellorto DHLA40 carbs.
(http://i871.photobucket.com/albums/ab274/avenga76/1975%20avenger/P1030994.jpg)
Feel free to make a post under the Avenger Related section and or Members Gallery section and tell us all about your Dodge 1500
AVENGA thanks for the welcome to the club. then I will post pictures of 1500 dodge models that exist in Argentina. Congratulations on that Hillman is beautiful. I love the intake manifold is very good.I forgot thanks for the manifold imformacion
cheap avenger in hamilton, $400, reg on hold complete car, looks pretty solid
http://www.trademe.co.nz/Trade-Me-Motors/Cars/Chrysler/hilman/auction-370000324.htm
looks good for that sort of dollar why are they always on the north island :(
Check out these 17" mags and tyres on TradeMe for $400....will have to flare your guards to squeeze the 205's in!!
http://www.trademe.co.nz/Trade-Me-Motors/Car-parts-accessories/Wheels-tyres/Alloy-wheels/auction-370719520.htm
Quote from: hunted on April 18, 2011, 08:21:11 PM
cheap avenger in hamilton, $400, reg on hold complete car, looks pretty solid
http://www.trademe.co.nz/Trade-Me-Motors/Cars/Chrysler/hilman/auction-370000324.htm
Sold for $865
1979 Chrysler Avenger GLS $3,850 ono.
Quote from: http://www.trademe.co.nz/a.aspx?id=374061801very tidy car all new brakes incl cylds reco steer rack airshocks new low pro khumo tyres flys through wof brought a year or 2 ago from deceased estate by chrysler crazy family now sadly selling to buy the next one. original wheels cntr caps and nuts with new tyres also there.very original car dont think jack and tools have ever been moved, all factory paperwork , options list service manual .
(http://images.trademe.co.nz/photoserver/97/170547797_full.jpg)
http://www.trademe.co.nz/a.aspx?id=376398501
Austin Hillman Avenger 1975??? (I didn't know Austin made Avengers ;) )
QuoteThis Hillman Avenger was purchased new in 1975 by my grandma - now that she is 88 it is time to sell this classic. The k's are correct, however it has been around the clock once already. It is really well looked after and still has the original paint colour. It has a brand new battery in the car. Unsure of the stereo etc. however there has been nothing changed to the car so would expect that this be radio only. She has really taken care of this car and is in great condition. Any questions, feel free to ask.
(http://images.trademe.co.nz/photoserver/47/171821847_full.jpg)
buy mine instead, its way more badass
Yes yours is much more bad ass. at least 90% more bad ass, if not much more.
Good luck with the sale of yours but don't think you are going to get away from the forum that easily. If you do sell your Avenger I still expect you to frequent the forum and post random crap. You are part of the Avenger family now so no getting out of your duties to the forum :)
BTW See if you can pimp the forum on your Avenger ad. like put something down the bottom saying "New owner must join the Avenger forum at http://www.avenger.co.nz" ;)
haha woops completly forgot to plug the forum, have edited auction
I had a 72 Avenger TC, All black interior, tombstone seats etc.....great car! had it for 14 years bought it off a a very good friend who had owned it from new and had it for 15 years....wanted to restore it but ended up selling it for $150 bucks when I moved away from my then location.....Never got paid for either LOL
Man that sucks. It would be an awesome car to own now days. Avenger TC's are really rare now days. I don't know of anyone who has one anymore.
A few of my friends used to own TC's but I don't know of any surviving cars left.
at least one hiding under blackberry at Wilf's...
sitting on dirt so a weeks worth of scrub cutting may result in tears... or TREASURE!
(http://img.photobucket.com/albums/v427/JoKerNZ/Stuff/DecWilfsParade013.jpg) last year
(http://img.photobucket.com/albums/v427/JoKerNZ/Stuff/2007_0702030.jpg) 2007
(http://img.photobucket.com/albums/v427/JoKerNZ/Stuff/2007_0702028.jpg)
It would so be worth pulling that thing out. If it is restorable it would be the only TC I know of on the road.
It would make an awesome daily driving for you JoKer, dump the subbie.
can it tow the rally car/4 ton dirt... lol
yea right, would be nice
Haha. Unfortunately no.
That's why I have the Charger. but yeah would still be nice to restore.
hence tis sort of a secret :P
i'm shit with some secrets...
I did sortoff start some TM add with parts from there BUT got well told off for selling bits that weren't mine by TM
Wilf knew about it and was happy as long as he got what he wanted BUT any offer to him is "a bit light"
can be fun to haggle with
(http://images.trademe.co.nz/photoserver/tq/63/173621363.jpg) (http://www.trademe.co.nz/motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-379918772.htm)
Auck
in fact save this link for mags 4x108 :P
http://tinyurl.com/3avmxpj
http://www.trademe.co.nz/motors/specialist-cars/competition-cars/auction-381258481.htm
(http://images.trademe.co.nz/photoserver/tq/36/174270836.jpg)
!!!!
edit : just noticed there is not "Avenger 'cars' for sale on TM" thread :P
Yes, That is a very cool car. Mike Courtney, the owner of that Avenger email me last night to tell me it was up for sale.
It is ex Ex Phil Ornstein rally car. It would be the most historically important Avenger left in NZ. It has been raced in the Heatway rally and Rally of NZ. Mike and Kirsten have also rallied it in the Targa 6 times.
It has a 2 litre brazil motor with a quick race and LSD.
You couldn't find a better example of a rally bred Avenger and I really hope in stays in NZ for the rally history of it.
I told Mike I would start a new thread for him so expect more info on it later today.
There's an Avenger compatible starter motor on TradeMe if anyone's looking for a spare?
http://www.trademe.co.nz/Browse/Listing.aspx?id=383748102
http://www.trademe.co.nz/Browse/Listing.aspx?id=384610247 already over my budget
(http://images.trademe.co.nz/photoserver/tq/12/170777312.jpg)
Very similar to a famous rally Avenger. Would be a good plate to have.
(http://www.groundsky.co.nz/hires.php?ImageID=130897)
Fibreglass Avenger panels. Could look awesome on a race car.
Quote from: http://www.trademe.co.nz/a.aspx?id=385738926Hillman Avenger / Imp Fibreglass Moulds
Hillman Avenger Airdam
Hillman Avenger Bonnet - Outer
Hillman Avenger Bootlid - Outer with Bobtail
sweet post pics when you can pls!
Sweet, Will do once he emails.
you guys know they are just the molds yeh? ie you will have to make the pieces yourselves
Yup. I have a mate who does the fibreglass for my race car. I was thinking of giving the molds to him and seeing how much they would be to produce and resell as finished products.
lol beaver yea they are mouldy :P not hard - mate made a GTR bumper for his skyline out of a mould
well sorrrryyy Mr Triumph lol
For sale again. '79 GLS Auto
Quote from: http://www.trademe.co.nz/a.aspx?id=3894062241979 Chrysler Avenger GLS
Automatic
Bought it January 2010
Great runner had no problems
Added a sound system, retractable seat belts and remote central locking
Selling because i've upgraded
car in as new condition
(http://images.trademe.co.nz/photoserver/5/178227305_full.jpg)
(http://images.trademe.co.nz/photoserver/91/178228291_full.jpg)
Whats the deal with the bent accellerator pedal
(http://images.trademe.co.nz/photoserver/5/178228105_full.jpg)
maybe a wonky foot
holy cow - I could not even get 2/3rds of that for my Legacy!
OTT
http://www.trademe.co.nz/motors/used-cars/chrysler/auction-374061801.htm
I loled at 1st pic (soo not an Avenger) then clicked thru the rest... nice
still at least $1500 too much for an old car, I don't care how "in" old cars are right now
Yeah I lol'd at the Valiant in the first and last pictures also. '69 VF Valiant Avenger :)
I do think both of them are pretty high. I paid $4K for mine but that was OTT.
I think the realistic price for a good Avenger going by recent sales would be around $2.5K-3K, maybe up to $3.5K for a real mint one.
y was there a valiant on there? when i also saw that auction i was a bit like wtf thats not an avenger!
souf islander...
nuff said
Because Valiants are cool! They need a random shot of a valiant in every auction if you ask me :)
It's why I have my Valiant Charger in my signature pic ;)
haha that one is pretty cool but im not gunna put pictures of the beetle or rx3 in an auction if im wanting to sell my avenger. they will make it look like SHIT
$4.6k for that red one?!>?!?!?!?!?! i dont even think i would get that for mine!
http://www.trademe.co.nz/motors/car-parts-accessories/other-accessories/auction-389090752.htm
this one has hawkes bay plates!
soz K only means its aprox a 1975...
http://en.wikipedia.org/wiki/Vehicle_registration_plates_of_New_Zealand
Quote from: kierbear on July 06, 2011, 08:44:10 AM
http://www.trademe.co.nz/motors/car-parts-accessories/other-accessories/auction-389090752.htm
this one has hawkes bay plates!
Quote from: http://en.wikipedia.org/wiki/Vehicle_registration_plates_of_New_Zealand#Cars_and_heavy_vehicles
1974-1976 with the allocation of plates beginning with "HB" to the Hawke's Bay region
ok fine!
I should learn to read more and less wiki links posting
yeah jeez was gunna say! ross told me that and i very much doubt that he would lie about that kind of thing! haha
Ross is a great source of old info like that. I hadn't heard of it either before Ross told us about it but I think it is a really cool idea.
havnt heard from him in a while. or aaron
Yeah. I see them both lurking around the forum now and then. Come on guys! post some stuff about your Avengers.
so they are stil alive yes?
I am guessing yes. If you view their member profile you can see when they were both last online. Both have been on the site in the last 24 hours so yeah give them a PM and rev them up :)
I thought we post stuff when our cars breakdown, must be why I've been quiet...nothing to report....haha
Well I did replace the alternator on Scarlett a little while ago and am planning to hook up the reverse lights sometime.
All Avengers have them, but they often aren't connected because Penny Pinching Chrysler wanted to save money...I've heard of Avengers being knocked back on WOF's in the old days because their reverse lights weren't working!!
And Yes the HB number was exclusive to Hawkes Bay I was told, by my car dealer cousin (and confirmed by wiki) Saw one on a 1974 Valiant when I was at the show in February. Definitely worth keeping it on my Alpine, rather than put a P plate on it!!
Yeah I want to do the same thing and hook up my reverse lights. Wonder if it will be harder getting them going on my 5 speed.
You can see the reverse light switch and cable in this photo.
(http://i871.photobucket.com/albums/ab274/avenga76/1975%20avenger/P1050036.jpg)
The reverse cable from the gearbox connects to the wiring loom behind the battery under the brake master cylinder, where there's a couple of wires protruding from the loom. Then holders and bulbs need to be put in the reverse lenses and the wires pushed on (including earth wires) and it should all go?!
easy peasy
Hillman Avenger 1600 Race /Rally Engine
Quote from: http://www.trademe.co.nz/a.aspx?id=394533538Have this little retro gem for auction.
We bought this years ago for one of my sons Avengers.
It had been built up for a rally engine about 1985.
My son used it for about a year until it dropped a valve. (off a stock head it was running not the modified one)
From what I remember I was told by the original builder it ran 116mph (about 185kph) in one of the Ashburton street sprints.
Anyway heres from what I remember
Big valve head (43mm), nice big inlet ports.Radical cam, nothing much happened before 3000rpm then pulled strong to who knows where.Lightened and skirted hepolite pistons,extra flywheel dowels,originally balanced.Nice bore,bottom end,valve guides,needs replacement piston.Will need a good hot tank and clean, fresh rings and shells and it would be a beaut.
Comes with headers and twin Solex 40s and manifold.Block converted to studs.
(http://images.trademe.co.nz/photoserver/32/181069332_full.jpg)
(http://images.trademe.co.nz/photoserver/75/181069375_full.jpg)
Hillman Avenger Grills
http://www.trademe.co.nz/a.aspx?id=394541602
(http://images.trademe.co.nz/photoserver/66/181076366_full.jpg)
hillman avenger engine and other parts
Quote from: http://www.trademe.co.nz/a.aspx?id=394540369hillman avenger engine up for auction.
Good running order.
Complete car available so if interested in other parts ask me a question and i can list it for you.
Pick up is in Pokeno just off SH1.
Many other cars breaking with ford falcon xe manual vauxhaull viva hc and datsun 260c also available
(http://images.trademe.co.nz/photoserver/20/178087620_full.jpg)
frik $250! 1600 w/ solex's
someone snap that up, bet it will go for more
Yeah it is a pretty damn good price. Don't know how well it will go on the street with nothing below 3,000RPM but I guess that is the way an Avenger engine is once it has been modified. Mine has nothing below 2,500RPM so it's not that much worse.
HB plates!
lol you said that last time with the same pic :
thats the same pic? shiiiit. those grilles are cool, the top one especially. never seen those ones before
Those are Alpine grilles.
The grill I am using for my 4 headlight conversion is exactly the same as the top one.
http://www.trademe.co.nz/motors/used-cars/chrysler/hillman/auction-396312495.htm
once this sells the guy can pay me for the wheels he took, so can someone please buy it lol it looks like a good project
lol, it would be a good project at half that price. my hunter (my first car) cost me $250
Yeah Agreed the price is pretty steep.
agreed also. if i dont get my wheels back soon hes gunna find his car on axle stands. it would be a good donor car, but yea, for 1/18th of the price
$1 reserve Chrysler Avenger
http://www.trademe.co.nz/a.aspx?id=396794240
man all the fun stuff is in the wrong Island or Dork'land
anyone going to go for that $1 one?
I would if it wasn't down in Invercargill. Would be a good buy for someone down south.
God thats tempting. If only I had the funds to drive down and tow it back.
depending on end price it would be worth getting it transported up wouldnt it?
possibly I know Jeffs are mega expensive. You need a Avenger Dave, why dont you buy it? lol
Avenger auto bellhousing!!!!!! 5 speed conversion anyone?
http://www.trademe.co.nz/a.aspx?id=398181630
on it like white on rice
Awesome! Just need to find a type 9 Sierra gearbox now.
because? can make anything fit no?
(clueless otherwise)
I picked up a type 9 today, so I'm keen on an auto bell housing too!!
lol go for it then - I cant afford a bidding war
edit : if the need is there I would grab a manual from Wilfs and steal Kierbears auto :P then send the bill
While the ladies might not agree, I've always said you're a gentleman Jared...lol
If it's going to cost $3000 to get it fitted I might have 2nd thoughts too!!
Reckon it might be cheaper to bring some 5 speeds in from Argentina??
or avengertiger it : toyota stuff iirc
like i said can make anything fit?
My Gearbox only cost $3000 because I wanted some bling that noone will ever see, but really I think you could get it done much cheaper. And now that Bygone have done all the hard work on mine and have a template they could probably make the adapter plate for a fraction of what mine cost because a lot of my cost was R&D.
I am really happy with they 5 speed, I was driving on the motorway and I changed down to 4th to pass a truck and I can't believe I used to drive around all the time in 4th, it just seems soo high revving.
5 Speed from Argentina would be interesting. Maybe we should ask some of our foreign members if they can ship a bunch out. Maybe include some 1800's.
hunter block/heads = 1800?
still not sure why the seirra is the 'must have'
edit : if these seem like newb questions , thats cos they are
Trouble is the Hunter motor is a bit of a dog...they took them out of the Iranian Hunters and put Avenger motors in...lol
Actually it's cheap and easy to just put a complete Pinto motor and Sierra 5 speed in an Avenger, but i don't want to lose that special Hillman-ness....haha
The Sierra isn't a must have, it is just easier because the clutch and driveshaft fit perfectly. They are all the same splines hillman and ford, and with the spacer then its the correct length so you don't need to do that much to them.
With say a Toyota T50 you need to make a new clutch and drive shaft. NZTiger went the T50 path so he would be the best to talk to about what he had to do to get the T50 going but with the Sierra it is just less stuff you have to do because it basically just slots in to place.
Hunter engine is a dog, It was out on the Humber so it was outdated even before they put it in the Hunter, really it is like a 50's engine so the Avenger engine is just lightyears ahead of it in engine design.
ah cheers makes sense now
Quote from: JoKer on August 09, 2011, 06:56:52 PM
lol go for it then - I cant afford a bidding war
edit : if the need is there I would grab a manual from Wilfs and steal Kierbears auto :P then send the bill
steal my car? well u can at least give me warning so i can tell the insurance company that i want 10k for it if it gets stolen lol
steal ross's son's auto lol ross has too many avengers anyway
BTW speaking of Auto's, I have a spare auto gearbox if anyone needs it. No bellhousing.
Avenger Alpine going cheap!!
Chrysler Hillman Avenger 1974
Quote from: http://www.trademe.co.nz/a.aspx?id=398652246This is a 1974 Hilman Avenger.
Has been sitting for a while with the intention of sanding it repainting it and putting a new interior and motor in.
Sad to see it go, it has potential to be a nice car I just don't need a project at the moment.
Bidders are welcome to view.
It dosn't go but was going last year.
Took the seats out which were dusty and had mildew on them.
As you can see it would need a lot of work to get going but it is a nice shape and there is no dents in any of the panel work.
Not sure what this is worth in its present state so will let the market decide.
As is where is.
Thanks
(http://images.trademe.co.nz/photoserver/1/183292501_full.jpg)
(http://images.trademe.co.nz/photoserver/26/183292526_full.jpg)
(http://images.trademe.co.nz/photoserver/33/183292533_full.jpg)
is that someone from here bidding on the AUTO housing? if so I will back off and you can have it :P
if not however... XD
Yeah that's me Jared!!
hah nice : all yours
you'll use it more than me :P
You don't need 5 gears anyway Jared. Most hillclimbs I would struggle to get out of 3rd.
yup is my theory too
holy bidding war batman!
ok who's george?
wow spendy! haha ross you wasting hi money?
Lucky I got the gearbox cheap...lol
Awesome stuff Ross. I will be interested to see how a 5 speed goes in a standard Avenger.
Now you will have no excuse for not keeping up on road trips.
Let me know if you need any help with the conversion.
Yes will be good, you know me Richard, I don't like to over-rev...lol
I will need help converting it as there's so much engineering to do.
Will run it past a local firm that's done some electric motor to gearbox adapter plates for me and see what they say.
The photos from your conversion will be invaluable!!
It will be interesting to see what rpm's Scarlett will do in 5th using the standard 3.89:1 rear axle?
I know the Sierra 5th gear is quite tall, so Scarlett may go below the equivalent 3.7:1 ratio of my Chrysler Avenger GLS?
The Triumph TR7 used a 3.9:1 rear axle with a 5 speed box and that was a 2 litre, so mustn't have been revving too high?
i knew of a rpm table chart/spreadsheet somewhere, you input the known ratios and it tells you speeds etc - will have a looksee
hot glue and zippy ties, just sayin :D
found it
http://www.clubsub.org.nz/forum/index.php/topic,11040.0.html
Quote from: lan_killa
Ive built up this excel spreadsheet to as accurately as possible Calculate and Graph Speed Vs. RPM for your vehicle.
Very simple to use, download it here: RATIOCALCGRAPH.xls (http://homepages.slingshot.co.nz/~moliver1/RATIOCALCGRAPH.xls)
Enter in your gear ratios, final drive ratio, tyre size and RPM limit and it will produce a graph showing RPM Vs. Speed in each gear. The spreadsheet is only setup to map out to a maximum of 10,000RPM. This can be used on 1, 2, 3, 4, 5 and 6 speed transmissions, simply enter 0 for your ratio on gears that you dont have.
If you want to see more detailed data, click on the DATA sheet at the bottom of the page.
To find out what your ratios are find your gearbox code on this site: http://www.catherineandken.co.uk/sti/trans.html
I hope some of you find a use for this
obvously from my 'other' forum :P
FYI here are the type 9 sierra gearbox ratios
1st 3.65:1
2nd 1.97:1
3rd 1.43:1
4th 1.00:1
5th 0.82:1
Rev 3.66:1
That XLS file is pretty much bang on. It says I get 2,800RPM@100KPH in 5th with 185/70/R13 and 3.70:1 diff. With a 3.89:1 that would work out to around 2,900RPM@100KPH.
maths is a predictable creature!
cool to confirm it with real world application
http://www.trademe.co.nz/motors/used-cars/other/auction-401590650.htm
mmm donor car, at best? lol way to ruin an avenger
i know someone who may actually buy that
i'd get it for the sik bonnet scoop...lol. if u move to napier jared, you could buy it!
sr20dett that bad boy
bahahahaha. like that guy that wanted to buy my car off me? win.
http://www.trademe.co.nz/motors/car-parts-accessories/ford/accessories/auction-402178105.htm
wheel time :P
http://www.trademe.co.nz/MyTradeMe/UpdateEmailOptions.aspx?s=5947120&redirect=%2fBrowse%2fSearchResults.aspx%3fsearchstring%3d4x108%26submit_keyword_search%3dSearch%26mcat%3d0001-0877-%26searchregion%3d100%26from%3dfav%26sort_order%3dprice_asc
4x108 few 14's and 17's under $400!
those would look cool on your car jared
the pink set :P
heatway rally book
Quote from: http://www.trademe.co.nz/a.aspx?id=403643450old nz heatway rally car book-programme1976,lots of car addverts-pictures of thr rally cars-and drivers-lots of pictures of the mighty ford escort-mazda rotary rx3-holden xu1-datsun-hillman avenger-toyota-porshe-etc,etc.
(http://images.trademe.co.nz/photoserver/8/185470908_full.jpg)
This is a very rare rally book from the year Andrew Cowan on the Heatway Rally of NZ.
I already have a copy of this rally book or I would have hit the buy now already. It has a couple of pages on Cowan's Avenger and an add from Todd motors etc.
A must have for any Avenger rally fan.
dont even know how i ended up on an art & framing website
http://artandframing.digitalretail.co.nz/Products.aspx?search=chrysler
http://www.ebay.co.uk/itm/Hillman-Imp-Husky-/190570746707?_trksid=p4340.m1374&_trkparms=algo%3DPI.WATCH%26its%3DC%252BS%26itu%3DUCC%26otn%3D5%26ps%3D63%26clkid%3D2553672845309644499
cooooooooool
CUUUTE!
Quote from: avenga on August 31, 2011, 09:38:19 AM
heatway rally book
(http://images.trademe.co.nz/photoserver/8/185470908_full.jpg)
This is a very rare rally book from the year Andrew Cowan on the Heatway Rally of NZ.
I already have a copy of this rally book or I would have hit the buy now already. It has a couple of pages on Cowan's Avenger and an add from Todd motors etc.
A must have for any Avenger rally fan.
bought this book this morning hope its in good nick lookin forward to the read.....got it for half the buy now.
Awesome! glad it went to a good home. I have a copy of it also and it is one of my favourite bits of Avenger history.
not on trademe but mate just offered me a set of 13" hotwires for $250
has 205's on them apparently and 1x 215
www.trademe.co.nz/a.asp?id=411072139
will fit my slicks a tad betterer :P and finally i have a budget for some parts!
whats anyone thingk they might go for? /ideal cutoff stupid price limit? its about $75~ ea for widening aye?
I want them! Yea Steel Sergeon is about $60+gst, Elite is about $75+gst
They are a bit too small and wide for me.
Can't wait for my 15x8 nascar rims :)
I already have 1 set of rims so if you need them more go ahead :P
wots ur TM name?
can get a set of 13" slicks for about $100 ( ex toyota racing series )
Mines "Burntwood" But yeah, depends what they go for, if they will fit on my car without flares and what mainfreight is going to sting me to get them down here. Otherwise you should buy them as they are closer to you.
I don't think 13x9 would fit without flares.
I run 13x7 with 205/60/R13 tyres on my race car and I had to roll the guards. We test fit some 15x8 with 225/50/R15 on my '75 and it sits about an inch or 2 outside the guard.
I dont know I've been doing some measuring up. with the measurements the guy gave the rears will problably stick out the guards by 1.5 inches. But I will be running 185/55/r13s so they will be fairly stretched, and hopefully just tuck under the guards. Im sure mr. Policeman wont like it though.
Yeah 185 on a 9" will be pretty stretched. my 225 on 8" is pretty much a flat side wall, but that's just the look I like.
I don't think I could get away with 15x9 with a flat side wall. 225 width is getting pretty big for a small car so I don't think I would want to go any bigger.
Kiera is running 14x8 on the back with 175/70/r14 tyres and they are pretty stretched.
mINE is an atv : no wprries about legal!
edit : very grey area so could be big fine one dahy.... (yes drunk
They just cleaned up that area recently, so I wouldn't be too certain anymore. Heaps of people got kicked off A reg. It took long enough: I haven't paid for a full G reg since 2004 or so. Luckily I now qualify for classic registration! :D
What are the costs for a car with Rally/Competition exemptions?
yea I re-registered as an ATV : car rego still on hold/exempt
I literally am in so much trouble if I get pinged...
BUT it does meet all requirements for ATV reg! (prove it doesnt I dare ya)
These caught my eye: roof racks.
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/exterior/auction-410363059.htm
and Twin Carbs
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/auction-410557157.htm
How long has that matt black car been up there? Looks to be a pretty decent parts car if you could argue him down a bit.
I saw those roof racks, but would they fit on an Avenger? They say they are for a VH Valiant, I own a VH Valiant and I can tell you they are a hell of a lot bigger than an Avenger.
I think it is the 2nd time that matte black Avenger has been listed so I would say it has been up there for a couple of weeks.
I was working under the impression they could be shortened, or where otherwise adjustable.
I am guessing you would have to cut it down.
You could do what Andrew A.K.A Hunted did on his Avenger (Now Sam A.K.A 1300Supers Avenger)
(http://www.rpmphotography.co.nz/var/albums/Oldschool-Nats-2011/IMG_1302.jpg)
(http://www.rpmphotography.co.nz/var/albums/Oldschool-Nats-2011/IMG_1331.jpg)
Although I am a big fan of racks like that - got one of my Van now (with proper gutter mounts) - I don't think they work for Avengers. Hunters and squarer cars: yes. Maybe an Estate could get away with it if done right, but it would take a lot to convince me.
(http://i916.photobucket.com/albums/ad7/Harry_Worth/Hannah/2010Pics059.jpg)
See: That looks good, and is essentially what that listing is for isn't it?
Check out the Sunbeam Ute in the same album...
http://media.photobucket.com/image/avenger%20estate/tremor63/Avenger%20and%20Sunbeam%20Owners%20Club%20sprint%202011/P7022605.jpg
Yeah those work well on a wagon with it's longer roof. I could see the VH Valiant ones working on a wagon but an Avenger sedan has a pretty small roof.
I love that pic of my car with those racks on. If only I could find a set!!
some real cool guy must have owned it before you huh? bet he now drives a sweet boned triumph.....
hows the 1600 coming along? any luck replacing the BHG?
Bad time to say that I used to have a spare set? Got a better one so scrapped it ;)
Shudve put it on trademe. Yes Andrew I must say you've got good taste when it comes to cars. Yea Its all going swimmingly. Its been pissing it down the past few days so I havnt done any work on it. However tomorrow I hope to finish scraping the baked on gasket off, put the new one on, Smash the head back on and fire it up.... fingers crossed. number one bore has a bit of a score in it but compression was ok so im going to pretend i didnt notice it. Next time the motor blows up it will be a full rebuild & rebore anyway. Or mite look at other engine options.
How hard is it to come across lotus motors? A stockish one of those would give just about the right amount of performance, every day drivability, and authenticity that you could hope for.
On the other hand I do really love the sound of the OHV. (Apart from my stuffed tappets never staying in tune)
au stink missed out on those steels by 5 mins! horse got a bargin
Just bought myself a Recond Head off trade me :P got it in the mail today, lookin good!
Au stink bro I forgot about those steelies!!
a bit puckeroo ah
i was hoping it was you too bro
Hey guys. I am just bidding on some mint new tail light lenses for my '75.
I have been looking for a perfect set for ages, they are pretty expensive at $35 each.
I would appreciate it if nobody would bid against me. My Trademe username is Richm
Cheers guys
Can you find out if the seller has another perfect pair? :D
Have found this website (was recommended it to me):
http://www.speedyspares.co.uk/n1stpage.htm
Check out their parts list! Group buy??
http://www.speedyspares.co.uk/ROOTES/AVENGER/avenger%20report.html
i bought some mint new ones and went to put them on and the screw holes didnt even line up :/ but all worked out
Thanks guys. I won those lenses.
Got one side for $35 but someone else was bidding on the other lens so I got that one for $49.
Seller onlt had one set.
1300Super these are you!
http://www.trademe.co.nz/a.aspx?id=420526076
if only two of them were badly slotted for nissan i would be in business! [looking at chucking an aussie diff into my van]
Quote from: 1300super on October 04, 2011, 04:54:29 PM
I love that pic of my car with those racks on. If only I could find a set!!
ebay! i just got some for the beetle coz they look badddd
For Kiera's Avenger?
http://www.trademe.co.nz/daily-deals/deal/1642
i sort of already have a chiffon type leopard print top to wear over other things lol. you know me too well!
I have my AVENJA Personalised Plate for sale...$950 to forum members or $995 through TradeMe...
http://www.trademe.co.nz/Browse/Listing.aspx?id=459277595
Just the thing for you Keira...no one will call your car an Escort ever again....haha
That is a pretty awesome plate.
Yes, being all letters with great pronunciation, I was surprised it was still available when I bought it in April last year!!
Got it to put on an imported or re-registered Avenger, but not needed now as I'm happy with my 1975 Alpine on original black plates.
Yeah I was surprised my AVENGA plate was still there. But I brought that back in like 2000 when personalised plates only cost about $400, they are so expensive now.
I am the same with my '75. People often ask why I don't put my Avenga plates on my '75 but I like my black plates.
And now that you can reregister a car and keep its black plates it makes it even harder to choose personalised plates over the black ones.
I know if you still have the old black plates for a de-registered car, they can be put back on when it's vinned, but if the old black plates are gone, can replacement ones be made in black or do they have to be white?
Also, can you swap P Plates with black ones while you own a car, so you can use it with the P Plates and then put the black ones back on when you sell it and keep the P Plates for your next Avenger?
You cant get old black plates remade period (in black or white). you would have to get a brand new plate with a new number/letter combination.
and I dont think you can take off a black plate for a P plate then go back to the black. Again, I think you woul have to get a brand new plate.
Quote from: oldschool on January 31, 2012, 10:42:42 AM
if the old black plates are gone, can replacement ones be made in black or do they have to be white?
No, you need to still have the original black plates in good condition to be able to revin it with the old plates under the new rules, they cannot make new black plates and they won't make white plates with the old number (although you may be able to personalise a white plate with the same number, see more below). If your black plates are missing or damaged the will issue you a standard white plate with the modern ABC123 numbering.
Quote from: oldschool on January 31, 2012, 10:42:42 AM
can you swap P Plates with black ones while you own a car, so you can use it with the P Plates and then put the black ones back on when you sell it and keep the P Plates for your next Avenger?
No. When you put personalised plates on a car they make you surrender your old plates and the old rego number is forever dead. for the new rules to work the de-registered car needed to have the black plates as its last set of plates when it was deregistered so once you switch to Personalised plates then your old black ones are dead.
If you sell a car with personalised plates and you want to keep the plates for your next car then you can go down to the post office and apply for a new white number plate to be issued and your Personalised Plate sort of becomes suspended until you register it on something else.
I know all this from experiance from my cars in the past. I did find a way physically keep your black plate but you can never use it again. I did this on my '80 so I still have the original black plates for it.
Here is what I did. First I let the rego lapse so it because de-registered but I didn't have to hand in the original JU2660 black plates.
Then I got it re-vinned with a new white plate AQL516, Then I personallised my plate getting AVENGA and surrendering the AQL516 white plate.
This doesn't help me much because I have no way of getting that black plate back on to the car. If you goto plates.co.nz they say JU2660 is already taken (by my old black plate) I could get JU266O with the letter o on the end instead of a zero and hope nobody notices.
I think the only time you can personalise an old black number is when the LTSA knows they have destoryed the old black plates, which is fair enough or you could have 2 cars driving around with the same plates, 1 legally and 1 not.
Quote from: oldschool on January 30, 2012, 07:33:33 PM
I have my AVENJA Personalised Plate for sale...$950 to forum members or $995 through TradeMe...
www.trademe.co.nz/Browse/Listing.aspx?id=444496194&ed=true
Just the thing for you Kiera...no one will call your car an Escort ever again....haha
lol is there a garauntee on that? nah i like my black plates
Hillman Avenger "Go Faster" bits. Bling Bling your engine bay and give it a little extra zoom with this dress up and speed package.
Quote from: http://www.trademe.co.nz/a.aspx?id=453072588Hillman Avenger old school speed equipment
Auction is for:
Avenger TC twin 1 3/8 carbs,manifold and 4 into 2 exhaust manifold.
Rampipes.
Airbox.
Accelerator cable.
Chrome tappet cover.
Chrome sump.
Exhaust 2 inti 1 flange and front pipe.
Manifold bolts and washers.
Exhaust manifold has a crack in it but is weldable.
(http://images.trademe.co.nz/photoserver/45/207952845_full.jpg)
(http://images.trademe.co.nz/photoserver/0/207952600_full.jpg)
(http://images.trademe.co.nz/photoserver/93/207952693_full.jpg)
mm chrome, but do not need. dont need more shit to polish
Hillman/Chrysler avenger parts - LOTS
Quote from: http://www.trademe.co.nz/browse/listing.aspx?id=457256776I Have a treasure trove of parts in my shed including complete engines, interior parts, glass, seats, door parts, doors, diffs, lights, dashboards, guages, 1 set of good cond 15" mags with 4x108 pattern, tailgates, ducting, carbs, ignition parts, engine parts, shocks front and rear, gearboxes, driveshafts, steering racks, front crossmembers, torsion arms etc.
I think all up i have 8 cars worth minus the bodies. I also have two whole cars for sale neither of which are in the system or driveable. They are $100 each. One is a 1974 hillman avenger estate stationwagon and the other is a 1974 hillman avenger sedan.
All heavy parts (whole cars and engines) are pickup only.
Please ask a question with what you would like and ill check the inventory and see if i have it then list it seperately.
This auction is for one wheel nut
yup. this is my parts guy- i havnt seen him in years though
months more like
if anyone needs anything from him, he is real straight up, he wnt bullshit you on the condition of things if you ask him. knows his stuff. he got them all for fuck all so im pretty sure he has no reason to rip anyone off
Sweet. I asked him some questions about the 15" rims and I am also looking for the center console out of a Chrysler Avenger.
oh yup. ive been round to a farm where he stores all his stuf. there is sooooo much stuff. windscreen rubbers, everything.i got my wheel nuts off his pink avenger lol coz they looked cool.
this miight interest Ross lol
http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/other/auction-464061741.htm
That's a good price.
Those wheel covers are too common Keira...gave Logan these classy ones for his 21st...!!!
http://www.trademe.co.nz/Browse/Listing.aspx?id=494114285
via Kierbeer
(http://images.trademe.co.nz/photoserver/35/219124935_full.jpg)
I have one of those. It is a must have if you want to do major work on your Avenger. It is like a Haynes manual on crack! It has all the tech drawings of the suspension parts, heaps of other measurements for if you need to straighten or repair the chassis. It goes in to much better detail than the Haynes manual does. I would say it is easily 3 times bigger than a Haynes.
lol $50 starting bid, i dont think so! thats what aaron is for lol
Aren't blokes useful...and if Aaron ever needs any nursing, he knows who to call...!!
Haha, must admit I enjoyed working on it and it was great stopping in at the British car museum and seeing my Superminx, I want a auto in my Avenger
What is the gearbox?
Its factory 4 speed automatic. Ill drop a box of beer at yours on my lunchbreak on wednesday or thursday aaron. ill try find a spot outta the rain to leave it at. Free nursing? i dont think so! i think i said something like "dont hurt yourself im nt in the mood for that today". It was pretty cool seeing the suerminx. Good destination for an avenger meet
also Ross Re: ur profile pic. Whats up with that bonnet? im highly disappointed
Try and keep up Kiera...black bonnets are all the rage!!
yea it needs flames at least
Avenger+black bonnet=cool
i think i might just keep mine all the same colour
Quote from: kierbear on July 24, 2012, 06:13:06 AM
i think i might just keep mine all the same colour
Yeah I think because yours is a lighter colour it would look better all the same colour.
Yep Kiera's car looks great in Ford Blue...LOL
Thankyou
http://www.bidbud.co.nz/526971810
Extractors Otago
Saw these twin carbs with Griffiths manifold on TradeMe....rare and a bit worse for wear!!
http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/engines/auction-550399575.htm (http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/engines/auction-550399575.htm)
Alloy head hunter by the port spacing
wut? learning something new now
mags
(http://images.trademe.co.nz/photoserver/tq/244025603.jpg) (http://oldschool.co.nz/2011/forum/index.php?/topic/36109-old-school-ford-13-cheviot-honeycombs/)
Dude would those totally fit my van ? their uber sick ae, they might be pretty dope on it ! hahaa
yup should be no issues at all
OS link leads to a Trademe link if your not a member on there
Quote from: nuget
13"x5.5. 4x108 old school ford pattern
Came off my mk1 cortina
Metallic gold finish
After 500 ONO
Well also fit :escort, anglia, capri, mk1,mk2
Here's the link: (pic speak for itself)
http://www.trademe.co.nz/Browse/Listing.aspx?id=552388845 (http://www.trademe.co.nz/Browse/Listing.aspx?id=552388845)
yea ford has the same stud pattern Mikey, my wheels came off a ford. thats pretty cheap if thyre not curbed or anything
Worked Hunter motor twin 45DCOE's starts at $400 (reserve not met)
http://www.trademe.co.nz/Browse/Listing.aspx?id=566698970 (http://www.trademe.co.nz/Browse/Listing.aspx?id=566698970)
(http://images.trademe.co.nz/photoserver/tq/256260022.jpg)
http://www.trademe.co.nz/motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-576291578.htm (http://www.trademe.co.nz/motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-576291578.htm)
(http://images.trademe.co.nz/photoserver/tq/258974301.jpg)
BRAND new 14"x7"s Turbos $450
Here's a complete Chrysler 1600 diff for sale in Timaru...has a 3.7:1 ratio...ideal for upgrading a Hillman 1600 and a steal at $25.
http://www.trademe.co.nz/Browse/Listing.aspx?id=580458203 (http://www.trademe.co.nz/Browse/Listing.aspx?id=580458203)
Here's an Avenger for parts or put back on the road, plus an auto gearbox he'll sell separately...go Jared!!
http://www.trademe.co.nz/a.aspx?id=600586238 (http://www.trademe.co.nz/a.aspx?id=600586238)
holy shit holy shitholy shit holy shitholy shit holy shitholy shit holy shitholy shit holy shit
***COBY EXTRACTORS*** ALL MAKES & MODELS 4,6,8CYL
$340 Avenger specific (In Q&A)
http://www.trademe.co.nz/motors/car-parts-accessories/performance/exhaust/auction-599546640.htm (http://www.trademe.co.nz/motors/car-parts-accessories/performance/exhaust/auction-599546640.htm)
some valves
http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/other/auction-598996483.htm (http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/other/auction-598996483.htm)
(no idea if inlet or exhaust) are these a good deal? could use a set myself for possible next rebuild edit lol I cant read INLET
Cam bearings
http://www.trademe.co.nz/motors/car-parts-accessories/vintage-parts/engines/auction-599936738.htm (http://www.trademe.co.nz/motors/car-parts-accessories/vintage-parts/engines/auction-599936738.htm)
2x 13"x8"s!
(http://images.trademe.co.nz/photoserver/tq/269894293.jpg)
http://www.trademe.co.nz/motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-600744749.htm (http://www.trademe.co.nz/motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-600744749.htm)
There is an Alpine/GLS on Trademe which is being parted out.
It would be a good source of parts for anyone looking to do a quad headlight conversion etc.
http://www.trademe.co.nz/Browse/Listing.aspx?id=612235175 (http://www.trademe.co.nz/Browse/Listing.aspx?id=612235175)
is it bad that I am reasonably interested in this, do you think if I play the "yay I won your whole car for $1 he would sell It LOL
haha, don't think that will work, but if you want a part then ask him how much in the questions and then just click the buy now and tell what parts you want.
he said he is open to offers on the whole car. It is up in Hastings so not to far to drive for you, or maybe Aaron or Kiera might be able to pick up some parts for you. do you need anything for your Alpine other than the auto gearbox?
The parts are selling pretty quickly. the current auction is http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/auction-612789540.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/auction-612789540.htm)
But that will close when someone uses the buy now so it is best to go to his members listing page and see what the current auction is. http://www.trademe.co.nz/Members/Listings.aspx?member=51976 (http://www.trademe.co.nz/Members/Listings.aspx?member=51976)
weirdest auction/listing setup EVER
and I thought I made things complicated sometimes
and that is why OS don't allow "offers" saves mucking around/lowballers
Yeah I don't like making offers on parts, I am always worried about lowballing and offending the seller.
I guess when you have that many parts then it is the easiest way to do it, you can't really make an auction for every part, this way people can just ask for what bits they want.
$350 the lot : $200 was my offer : space and the fact I dont have the money for another parts car is going against me
hmmm i have not heard of this "Glen" and i cant believe i havnt seen the auction either. im not even certain i need anything at the moment
In the dealership i worked at, all the 1500TC Avenger from Todds we sold, were black interior trimmed. BUT, a customer could at ordering time with dealer, have any colour scheme or trim option, at a slightly higher price as it interupted the std line build of that days production. I remember our dealer principle at the time[a 40 year-old] took a TC off our floor and was invited down to the Levin race track,[ still going in those days,] and blew away MK3 Cortinas from the Ford dealership in town, whom were also invited to this promo. He actually broke the then[ std up to two litre] saloon car lap record !
http://oldschool.co.nz/2011/forum/index.php?/topic/44963-fs-hillman-avenger-tail-lights-palmerston-north/ (http://oldschool.co.nz/2011/forum/index.php?/topic/44963-fs-hillman-avenger-tail-lights-palmerston-north/)
some taillights on OS (Peter W selling parts)
Quote from: avengerparts on October 09, 2013, 01:27:07 PM
In the dealership i worked at, all the 1500TC Avenger from Todds we sold, were black interior trimmed. BUT, a customer could at ordering time with dealer, have any colour scheme or trim option, at a slightly higher price as it interupted the std line build of that days production. I remember our dealer principle at the time[a 40 year-old] took a TC off our floor and was invited down to the Levin race track,[ still going in those days,] and blew away MK3 Cortinas from the Ford dealership in town, whom were also invited to this promo. He actually broke the then[ std up to two litre] saloon car lap record !
The 1500TC I owned many years ago must have been a special customer order as it had light tan/white trim and brown carpets.
Two tidy Avenger TC hubcaps for sale here, buy now $35.
If anybody wants a full set for there Avenger I have two that they can have.
http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/exterior/auction-777582179.htm (http://www.trademe.co.nz/motors/car-parts-accessories/parts-other-makes/exterior/auction-777582179.htm)
kinda neat
Hey guys, Recently my Hillman Avenger Alpine 1973 failed its WOF and has been off the road for a couple of weeks now. The only part i need is a LEFT FRONT SHOCK as its leaking.
please let me know if you can help :)
i appreciate it
Engine is back:
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/auction-782472847.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/auction-782472847.htm)
Guy from Waiheke is parting out:
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/suspension/auction-783383987.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/suspension/auction-783383987.htm)
auto gearbox with engine:
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/auction-782428671.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/auction-782428671.htm)
Haha oh I would make an offer but this guy seems like he doesn't want to sell it
Hi Everybody. I have a Chrysler/Hillman Avenger Monsoon for sale at $100.
I have a Chrysler Avenger towbar for $100 as well...doesn't fit Hillmans as it goes behind the bumper.
PM me if interested.
maaayte just seen the monsoon heh
bulk lot of parts here
http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/auction-914893540.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/auction-914893540.htm)
hastings
(https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-xpt1/v/t1.0-9/11223636_10203244908561890_4099658330764192602_n.jpg?oh=d158ed6e8f36d1018719c47f17b7b0f1&oe=5651018B&__gda__=1447410050_773750a35f6ceea2daffaa6e4c119786)
kinda keen anyone else?
https://www.facebook.com/photo.php?fbid=10203244908561890&set=gm.1173867435962901&type=1&theater (https://www.facebook.com/photo.php?fbid=10203244908561890&set=gm.1173867435962901&type=1&theater)
HE'S ASKING 150$
I can't get the link to work Jared...maybe I can look up his FB name?
its a "closed" group, you need to apply to view
"Michael Leask's (https://www.facebook.com/michael.leask.7?fref=photo) post in classic cars and wrecks nz for sale (https://www.facebook.com/groups/912331325449848/)"
^^links in there to profile & group to join^^
Hi all, have got some new heavy duty strut mounts in stock...$75 for one or $140 for two delivered to members...PM me if you want them...limited stock!
NEW Hillman/Chrysler Avenger/Sunbeam 1976-81 Heavy Duty McPherson Strut Top Mount with 9/16" bore.
It has an extra mounting hole for competition use if required, otherwise secure it using the 3 standard mounting holes. This rubber bush 'top hat' is needed when replacing worn/leaking 1/2" threaded struts used in the 1970-75 Avenger with 9/16" ones.
Hiya guys, there's someone down in hastings that has a four bay garage FILLED with avenger parts. Listing number #945712400
=P yea we know
we keep all the trademe lisitning tucked in over in this thread : http://www.avenger.co.nz/forum/index.php?topic=16.300 (http://www.avenger.co.nz/forum/index.php?topic=16.300)
but cheers for the reminder! what a collection eh, how's you car getting on? Your cousin Sam asked me about headlight switches before you bought yours
these extractors keep popping up & not coming down in price
http://www.trademe.co.nz/a.asp?id=949989801&member_hash= (http://www.trademe.co.nz/a.asp?id=949989801&member_hash=)
(http://trademe.tmcdn.co.nz/photoserver/tq/392339648.jpg)
might be of use to someone
Hello!
Yeah got the headlight switch in, and the car running nice. Just gotta take her in for a WOF and get her legal. Fully cleaned the interior, literally :D buff and polish on the exterior aswell.
Yea hes in waipawa and quite keen on selling everything to get his shed space back as it takes up alot of space. Nothing usually comes down in price from that place
one of our forum regulars
HILLMAN~CHRYSLER AVENGER HEAD GASKET SET 1970-81 (http://www.trademe.co.nz/link.aspx?i=12146&id=1107749841&t=se&s=10939725&c=168)
(http://trademe.tmcdn.co.nz/photoserver/plusw/464183937.jpg)
$70.00
HILLMAN~CHRYSLER AVENGER STARTER MOTOR 1973-81 (http://www.trademe.co.nz/link.aspx?i=12146&id=1107736097&t=se&s=10939725&c=168)
(http://trademe.tmcdn.co.nz/photoserver/plusw/464175525.jpg)
[/size]$120.00
AVENJA Plate for Hillman/Chrysler & Dodge Avengers (http://www.trademe.co.nz/link.aspx?i=12146&id=1107498882&t=se&s=10939725&c=168)
(http://trademe.tmcdn.co.nz/photoserver/plusw/345988301.jpg)
[/size]$995.00
MACKAZ, on 09 Nov 2016 - 5:38 PM, said:
Unknown condition. Got as part of a deal. One carb spindles broken.third carb for bits. Make me an offer. Text only 0211204246
from oldschool.co.nz (http://oldschool.co.nz/index.php?/topic/54572-fs-avenger-twin-carbs-and-manifold-whangarei/#entry1779220)
Not sure if this one has made it to trademe yet but its for sale in a Closed Facebook Group
(http://imgur.com/am46gyHl.png)
Link if you'd like to try & view or join https://www.facebook.com/photo.php?fbid=1328897787199521&set=pcb.1564493646944889&type=3 (https://www.facebook.com/photo.php?fbid=1328897787199521&set=pcb.1564493646944889&type=3)
It doesn't appear to be listed there anymore.
hmm you're right sold? or withdrawn, you keen for another orange ruffy?
Quote from: oldschool on May 12, 2017, 05:57:29 PM
It doesn't appear to be listed there anymore.
hah this is why... http://www.avenger.co.nz/forum/index.php?topic=1001.0 (http://www.avenger.co.nz/forum/index.php?topic=1001.0) :D
and oh wow 1000+ threads? Congrats Avenger.co.nz wonder how many are mine lol
most of them probably!!!
Quote from: JoKer on May 22, 2017, 05:25:20 PM
hah this is why... http://www.avenger.co.nz/forum/index.php?topic=1001.0 (http://www.avenger.co.nz/forum/index.php?topic=1001.0) :D
and oh wow 1000+ threads? Congrats Avenger.co.nz wonder how many are mine lol
Only 70
General Statistics - JoKer
Total Time Spent Online:68 days, 21 hours and 8 minutes.Total Posts:1439 posts Total Topics Started:70 topics Number of Polls Created:2 polls Number of Votes Cast:5 votes
You are second behind me, I am at 89 topics started. But you are kicking my butt in time spent online, I am only on 39 days.
Tons of people are on around 20-40 topics so it all adds up.
Congrats everyone on making this forum really great, roll on 2000 threads!!!
And in other Avenger.co.nz news, I just renewed the Avenger.co.nz domain for another four years. We are already over six years old. And we just went over 350 members!!!
1500 "s" head on the bay LOL
(https://scontent.fakl1-2.fna.fbcdn.net/v/t1.0-9/34278678_2075924582733161_3583067988422557696_n.jpg?_nc_cat=0&oh=548f35e0690779bf5a7686a726cf3fbc&oe=5BB2117E)
might need resto LOL
source link https://www.facebook.com/1450811508577808/photos/a.1451997338459225.1073741828.1450811508577808/2075924579399828/?type=3&theater (https://www.facebook.com/1450811508577808/photos/a.1451997338459225.1073741828.1450811508577808/2075924579399828/?type=3&theater)
https://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/listing-1764333532.htm?rsqid=2126c6d011db4eaa851c934e1b220d6e (https://www.trademe.co.nz/motors/car-parts-accessories/chrysler/engines/listing-1764333532.htm?rsqid=2126c6d011db4eaa851c934e1b220d6e)
(https://trademe.tmcdn.co.nz/photoserver/plusw/818707352.jpg)
QuoteHillman Avenger cylinder head, brand new bare head. Not sure what model engine
NOS Head : this is Ian Sutherlands account from Tirau : the Sunbeam (And Rootes / Hillman Spares guy
I'm quite tempted on this one myself but if there's a better deserving member on here that needs it I might get it next time he relists (or offers)
Otago
www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/listing-1873287019.htm (http://www.trademe.co.nz/motors/car-parts-accessories/chrysler/other/listing-1873287019.htm)
(https://trademe.tmcdn.co.nz/photoserver/plusw/916026372.jpg)
Quotethis sale is for one tidy stainless hub cap delivered ---i have loads of parts off these cars even sum new stuff---just ask i am about
(https://trademe.tmcdn.co.nz/photoserver/plusw/916058305.jpg)
(https://trademe.tmcdn.co.nz/photoserver/plusw/916058476.jpg)
(https://trademe.tmcdn.co.nz/photoserver/plusw/916059045.jpg)
(http://imgur.com/EpO9DtMl.png)
(http://i.imgur.com/EpO9DtM.png)
Link : www.trademe.co.nz/a.aspx?id=1993001865 (http://www.trademe.co.nz/a.aspx?id=1993001865)
Quote
- Trade Me Motors >
- Car parts & accessories >
- Interior >
- Floor mats[size=78%] [/size]
Hillman Avenger Carpets "BUY NZ MADE"
Listing #: 1993001865
Manukau, Auckland, NZ
New item
(https://trademe.tmcdn.co.nz/photoserver/full/179500282.jpg)
Replacement carpet sets for Hillman Avengers.
We also have Hunter - Hawke - Super Snipe - Imp - Super Minx - Rapier - Humber 80 - Humber 90 - Subeam Alpine etc etc
All available in 10 colours including Black.
All carpets in genuine Tufted Cut pile carpet.
We have matching Car Mats & Bootmats.
Full range of insulations for Engine Bay - Sound Deadning - Underfelt and Dynamat available
They have been selling them on Trademe for years. I put a set of those in my 1975 back in 2011, just buying another set for my wagon.
seems cheap to me! / Good value!
Yeah, just got them to quote for one for my wagon, I need to get them modified for the bigger transmission tunnel and firewall, so I'm buying an extra bit of carpet which a local trim shop is going to cut and stitch in, but here are the prices they gave me.
Avenger Floor Carpets $310
Boot mat (Wagon) $ 80
Carpet per metre $ 50 1800mm wide
(http://imgur.com/3WtuWwNl.png)
(http://i.imgur.com/3WtuWwN.png)
Link : www.trademe.co.nz/a.aspx?id=1995035033 (http://www.trademe.co.nz/a.aspx?id=1995035033)
QuoteDescription
This auction is for one rear RH quarter light window for a 1977 - 1981 Chrysler Avenger.
If you own a nice Avenger, then these spares are a must-have, as glass has a habit of getting broken.
You can see in the photos, I have the 4 quarter light windows, front windscreen (or windshield), rear window and drivers door main window. You are welcome to buy the lot, or let me know which one you want and I can start an auction.
All windows are in good condition for their age.
There are also 3 rear window rubber seals which appear to be in surprisingly good condition, and one front windshield rubber in average condition with a little bit of perishing etc. Note there are no expander inserts with these rubbers.
Make me an offer for the lot :)
I am happy to freight the small windows, but not the front and rear windshields and rubbers due to their size and fragility, unless the prospective buyer can offer a good solution, which would be at the buyers risk and cost.
worth getting ion contact I reckon just for the Rubbers
I could have used that today 😂
hah still made it work!
Found stickers : ball head allen key (hope its the right size) and loaded up ready for the morning!
(http://imgur.com/i4nQaY9l.png)
(http://i.imgur.com/i4nQaY9.png)
Link : www.trademe.co.nz/a.aspx?id=1999319414 (http://www.trademe.co.nz/a.aspx?id=1999319414)
QuoteDescription
this sale is for one tidy stainless hub cap delivered ---i have loads of parts off these cars even sum new stuff---just ask i am about
Seller location: Dunedin, Otago, NZ
Link to Seller's profile : https://www.trademe.co.nz/Members/Listings.aspx?member=4193586 (https://www.trademe.co.nz/Members/Listings.aspx?member=4193586) [/size][/font]
i just fitted one of those autodec carpets to my orange car they don't fit great in fact they fit badly,but better than nothing i found mine was to big around the tunnel anyway richard so test fit yours first before you get it made bigger.
bit of trimming and pulling needed and its still a bit baggy around tunnel which is a pain.
The autodec one for my 75 was baggy around the tunnel also, so maybe it would fit.
eBay (UK) : https://www.ebay.co.uk/itm/Hillman-Avenger-MK1-Pair-of-Front-Wings/254189628139?fbclid=IwAR2vbL7zEQPfGXkw6Z5QHkjWvzJLluadvKOZ7UnR_pGrj7aYs3tAbbKJUa0 (https://www.ebay.co.uk/itm/Hillman-Avenger-MK1-Pair-of-Front-Wings/254189628139?fbclid=IwAR2vbL7zEQPfGXkw6Z5QHkjWvzJLluadvKOZ7UnR_pGrj7aYs3tAbbKJUa0)
(http://imgur.com/Z8tJmEjl.png)
(http://i.imgur.com/Z8tJmEj.png)
ooh
(http://imgur.com/RbWkWQ1l.png)
(http://i.imgur.com/RbWkWQ1.png)
yep there is an ASOC Member discount too
can get a whole parts car for that!
but still do want, even if I don't need them just yet!
(http://imgur.com/bOfCsUal.png)
(http://i.imgur.com/bOfCsUa.png)
Linky Dinky : www.trademe.co.nz/a.aspx?id=2292121037 (http://www.trademe.co.nz/a.aspx?id=2292121037)
Re conditioned 1300 Engine for $1k (looks nice)
QuoteHillman Chrysler 1300 engine,
Done 3,000 km since full recondition.
can sell as a long block or complete.Have replaced with a 1600 so surplus,If you are looking to recon or replace your engine this would be a cheaper option as selling well below what it has cost.
(https://trademe.tmcdn.co.nz/photoserver/plusw/1108298934.jpg)
Sorry to be a debbie Downer but I dont think it's worth that much but it Might be to someone who wants one glws
that will probably outlast anyone who buys it though!
That?s Kevin?s engine. I?ve seen it in person and it?s a very pretty 1300, he replaced it with a 1600. I?ve been on a few cruises with Kevin when she had this 1300 in his Avenger and it went really well. He is a member here
(http://imgur.com/QEBdaitl.png)
(http://i.imgur.com/QEBdait.png)
Link to G box : https://www.trademe.co.nz/a.aspx?id=2405531188 (https://www.trademe.co.nz/a.aspx?id=2405531188)
(https://trademe.tmcdn.co.nz/photoserver/plusw/1155394294.jpg)
Seller is Ross aka oldschool (http://www.avenger.co.nz/forum/index.php?action=profile;u=29) on these forums
https://www.trademe.co.nz/Members/Listings.aspx?member=5220342 (https://www.trademe.co.nz/Members/Listings.aspx?member=5220342)
Ross is still trying to clear some bits
(http://imgur.com/lX2JMRrl.png)
(http://i.imgur.com/lX2JMRr.png)
LINK : to Gear Box https://www.trademe.co.nz/a.aspx?id=2517066868&member_hash=cadd46d681c1b791a8e9224b00ee4c33d597c6a326929bb2e6&tm=email&et=46&mt=D2763320-CBD5-41AC-AFD4-EB154754D2BA (https://www.trademe.co.nz/a.aspx?id=2517066868&member_hash=cadd46d681c1b791a8e9224b00ee4c33d597c6a326929bb2e6&tm=email&et=46&mt=D2763320-CBD5-41AC-AFD4-EB154754D2BA)
I have other parts not listed as well..like genuine Cibie Alpine headlights!
Parts on Facebook
(http://imgur.com/QrldrEtl.png)
(http://i.imgur.com/QrldrEt.png)
LINK : https://www.facebook.com/marketplace/item/2571809559728625/ (https://www.facebook.com/marketplace/item/2571809559728625/)
from FB
(http://imgur.com/neGajAbl.png)
(http://i.imgur.com/neGajAb.png)
"LINK (https://www.facebook.com/groups/1608911092749139/2322479571392284/?comment_id=2322835011356740&reply_comment_id=2322839101356331¬if_id=1593640772719244¬if_t=group_comment_mention)"
another from FB
(http://imgur.com/KH5YnqBl.png)
(http://i.imgur.com/KH5YnqB.png)
LINK (https://www.facebook.com/groups/450943631764848/permalink/1423729754486226/?sale_post_id=1423729754486226&ref=messenger_share)
Murray from Motueka has listed a couple of things
(http://imgur.com/Pvm7AaQl.png)
(http://i.imgur.com/Pvm7AaQ.png)
https://www.trademe.co.nz/Members/Listings.aspx?member=1041327 (https://www.trademe.co.nz/Members/Listings.aspx?member=1041327)
Bunch of NOS parts just been listed
(http://imgur.com/y521aerl.png)
(http://i.imgur.com/y521aer.png)
LINK (https://www.trademe.co.nz/members/listings.aspx?member=1784426&bof=GTaj9OYQ&cid=1)
(http://imgur.com/xwVSFfMl.png)
(http://i.imgur.com/xwVSFfM.png)
Quote from: JoKer on July 03, 2020, 10:33:31 AM
another from FB
Im not on Facebook - does anyone know if this engine is still available or how to contact the posting person?
Cheers Brett
(http://imgur.com/KH5YnqBl.png)
(http://i.imgur.com/KH5YnqB.png)
LINK (https://www.facebook.com/groups/450943631764848/permalink/1423729754486226/?sale_post_id=1423729754486226&ref=messenger_share)
Quote from: JoKer on July 02, 2020, 10:33:40 AM
from FB
(http://imgur.com/neGajAbl.png)
(http://i.imgur.com/neGajAb.png)
"LINK (https://www.facebook.com/groups/1608911092749139/2322479571392284/?comment_id=2322835011356740&reply_comment_id=2322839101356331¬if_id=1593640772719244¬if_t=group_comment_mention)"
Quote from: JoKer on July 02, 2020, 10:33:40 AM
from FB
(http://imgur.com/neGajAbl.png)
(http://i.imgur.com/neGajAb.png)
"LINK (https://www.facebook.com/groups/1608911092749139/2322479571392284/?comment_id=2322835011356740&reply_comment_id=2322839101356331¬if_id=1593640772719244¬if_t=group_comment_mention)"
Hi Brett
sorry I just followed the link for the Intake : it says its sold
https://www.facebook.com/groups/450943631764848/permalink/1423729754486226/?sale_post_id=1423729754486226&ref=messenger_share (https://www.facebook.com/groups/450943631764848/permalink/1423729754486226/?sale_post_id=1423729754486226&ref=messenger_share)
I've asked on the motor for you
Jared
Hey Brett.
Robert, the guy selling the motor is my neighbour, so I gave him a text. The motor has been sold, but I can email some of my other friends to see if they have any spare motors.
Hi Guys and apologies for the slow reply - work has been overwhelming. The ol girl has dropped a cylinder - Had the head done in 2019 but still fires short one cylinder so have stripped it back down again. Back in the day Dad used to get gaskets over the counter but thats not the case these days - how time has marched on. I haven't pulled the piston assembly yet and wasn't exactly looking for another project - got enough of those on my own cars let alone fixing and repairing the mileage my brothers took out of the ol girl over the years. Its definitely not a spark issue and the compression test shows no.1 cylinder lucky to get to 60 psi so something definitely going on. The saving grace is I made found enough space in my garage to get her undercover however Mothers car is now sitting outside and I am getting the odd sideways glance at my (lack of) speed in getting the yellow beast up and running again
https://www.trademe.co.nz/a/motors/car-parts-accessories/vintage-parts/electrics/listing/3166302174 (https://www.trademe.co.nz/a/motors/car-parts-accessories/vintage-parts/electrics/listing/3166302174)
(https://jaredm-nz.tinytake.com/media/109e0e1?filename=1626040047065_TinyTake12-07-2021-09-47-20_637616368444623356.png&sub_type=thumbnail_preview&type=attachment&width=1198&height=460&&salt=NTYwNTU1MV8xNzQyNDYwOQ)
AND https://www.trademe.co.nz/a/motors/car-parts-accessories/parts-other-makes/exterior/listing/3171634424 (https://www.trademe.co.nz/a/motors/car-parts-accessories/parts-other-makes/exterior/listing/3171634424)
(https://jaredm-nz.tinytake.com/media/109e0fa?filename=1626040954405_TinyTake12-07-2021-10-02-28.png&sub_type=thumbnail_preview&type=attachment&width=798&height=139)
disclaimer : none of these are mine & I am not affiliated with the sellers
(https://jaredm-nz.tinytake.com/media/120ce2c?filename=1643659703935_TinyTake01-02-2022-09-08-16_637792565013079347.png&sub_type=thumbnail_preview&type=attachment&width=536&height=360)
https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/accessories/listing/3453929536 (https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/accessories/listing/3453929536)
QuoteDescription
Hillman Avenger & Chrysler Avenger Parts.
Have spare parts available.
Have engine & steering & running gear & interior pieces doors glass etc but ask & see what I can spare. Have wagon/estate & Sedan Parts.
Will also buy parts i need to finish my projects or swap parts will also consider to buy wagon or sedan that need finishing or wrecks
Im after if anyone has spare
Wagon tail lights
High back avenger seats (tombstones)
Chrysler bonnet badges
Auto transmissions
Good engine mounts
$1 gets you a bolt
eBay :
Cricket Tail Light (One side) (https://www.ebay.com/itm/353435063738?_trkparms=amclksrc%3DITM%26aid%3D1110018%26algo%3DHOMESPLICE.COMPLISTINGS%26ao%3D1%26asc%3D239134%26meid%3D5c4b0a45ba95470bb0cc3a997cf049af%26pid%3D101196%26rk%3D1%26rkt%3D12%26sd%3D265334408111%26itm%3D353435063738%26pmt%3D1%26noa%3D0%26pg%3D2047675%26algv%3DItemStripV101HighAdFeeWithCompV3RankerWithKnnRecallV1%26brand%3DLucas&_trksid=p2047675.c101196.m2219&amdata=cksum%3A3534350637385c4b0a45ba95470bb0cc3a997cf049af%7Cenc%3AAQAHAAABEA%252FJiT7ssNXrEsx1zZncFUUkLU8ikMh%252FiWOsxkTqeqIbE5K4lpcDSKjAfQ%252F1if83xfL%252FcwBtfGSfYaggi%252B3rYYM%252FelvbRU4mXbe7uDBn8YCMZqZX%252BKMk4AUmrHzx3%252BO4ZAk%252FUjPkadaaPX5vkbAeMC8i4OETpaKU9jHtxqgJDWs5rmIBmFbcRHYvMpW%252BueekfgftNjedkH%252FTxZ%252FZLxMK%252Fx%252FpknaRHwdQZT1b4lI0%252FUlYrcz2XlYg8G1eOOMall0Hvz3IbX82RKt6b0FLoielwh%252BzvUpMTtK74ypel110PCJosUO1%252FJgFlKCMvrohxBoqkKASLrmWRxXCzJA%252B9XLlwEFjEzZzEpE%252BnQ4cuBopCXz8%7Campid%3APL_CLK%7Cclp%3A2047675&epid=2098153184)
(https://akiwijoker.tinytake.com/media/12b334f?filename=1654423232985_TinyTake05-06-2022-10-00-23_637900200265143084.png&sub_type=thumbnail_preview&type=attachment&width=1198&height=524)
Key Lock set : (https://www.ebay.com/itm/265432630194?_trkparms=amclksrc%3DITM%26aid%3D1110018%26algo%3DHOMESPLICE.COMPLISTINGS%26ao%3D1%26asc%3D239134%26meid%3D5c4b0a45ba95470bb0cc3a997cf049af%26pid%3D101196%26rk%3D2%26rkt%3D12%26sd%3D265334408111%26itm%3D265432630194%26pmt%3D1%26noa%3D0%26pg%3D2047675%26algv%3DItemStripV101HighAdFeeWithCompV3RankerWithKnnRecallV1&_trksid=p2047675.c101196.m2219&amdata=cksum%3A2654326301945c4b0a45ba95470bb0cc3a997cf049af%7Cenc%3AAQAHAAABEA%252FJiT7ssNXrEsx1zZncFUUkLU8ikMh%252FiWOsxkTqeqIbE5K4lpcDSKjAfQ%252F1if83xaRc8MVmq0JxkrpahNpFofcdQi%252BX%252FZ2NKzxrdsMC0jRZP6dgq2UnIj7KC98dQj3dAIe4gmDGH5Ap3aVD0BuyLvxZo44hKiRQ8hNY3ulmcVNamu2a7ItaT6W2FkeXIHmFusZrHFBkpSkWszGfi1jGN6xETPo%252FR0Wv5tN67fY1V3vrQMw1YBfc1LXcaUWUiE5tlc%252BUNLkvJYQrWL6P%252BgU9qtaQ1c27CxgmMmjs677v4GxzsGGNesRGnlMSa8Zs53eZHgIb2eSWYWG82l63FKdA%252BaTBRkHHGgwRtHx6Aib3D3%252FR%7Campid%3APL_CLK%7Cclp%3A2047675&epid=19029102611)
(https://akiwijoker.tinytake.com/media/12b3350?filename=1654423288514_TinyTake05-06-2022-10-01-16_637900200841314896.png&sub_type=thumbnail_preview&type=attachment&width=1199&height=587)
useless but fun to look :P
QuoteHillman Avenger parts for a car I no longer own…
Closes: 2 hrs 55 mins
Thu 4 Aug, 12:13 pm
Description
The deeper you dig, the more you find…..
I had great plans for my Avengers but moved on many years ago.
So this time we have:
1: Brand new Avenger boot lock complete.
2: a brand new pinion for a LucaS M 35J starter motor plus one other in good condition.
3: Two brand new brush assembly’s for a Lucas M 35 J starter motor.
4: I think a brand new bearing for a manual gearbox, had to have the groove specially machined to the outside.
5: A crankcase breather unit- not sure if strictly for an Avenger but brand new.
6: a clutch arm and a clutch release bearing, not new.
7: a fan switch- not new.
8: a few other bits Avenger related.
WYSIWYG.
Yes I'm bidding : no I don't need anything & wont go much higher
https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/interior/listing/3701983074 (https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/interior/listing/3701983074)
(https://jaredm-nz.tinytake.com/media/130d38a?filename=1659561403185_TinyTake04-08-2022-09-16-35_637951581997092053.png&sub_type=thumbnail_preview&type=attachment&width=1199&height=617)
Quote from: JoKer on August 04, 2022, 09:17:24 AM
Yes I'm bidding : no I don't need anything & wont go much higher
https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/interior/listing/3701983074 (https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/interior/listing/3701983074)
(https://jaredm-nz.tinytake.com/media/130d38a?filename=1659561403185_TinyTake04-08-2022-09-16-35_637951581997092053.png&sub_type=thumbnail_preview&type=attachment&width=1199&height=617)
Henry won that auction.
Usually if I know who the other person bidding on an auction is I will email them so I don't go in to a bidding war with another forum member.
There was another parts lot last week that went for like $127
haha yeah I recognised the name too :P he won
impulse purchase of the day
only look a little buggered
Nice! btw. I have ton of old hillman rear lights that I have collected over the years.
I have bought a few bulk loads of parts and they always seem to include tail lights. The tail lights on my 75 are NOS, and all my other Avengers are Chrysler wagons, so if anyone ever needs tail lights then let me know
From Facebook almost looks like Ron's but another in the 04
(https://akiwijoker.tinytake.com/media/1363fbd?filename=1665178247118_TinyTake08-10-2022-10-30-13.png&sub_type=thumbnail_preview&type=attachment&width=1198&height=604)
LINK : https://www.facebook.com/commerce/products/parting-a-hillman-avenger/5406742196109641?ref=messenger_share&rt=54 (https://www.facebook.com/commerce/products/parting-a-hillman-avenger/5406742196109641?ref=messenger_share&rt=54)
I have Ron's Avenger exactly same colour
Did anyone see, or respond to the FREE parts listed on FB over the break?
(https://jaredm-nz.tinytake.com/media/13d131f?filename=1672960015304_TinyTake06-01-2023-12-06-47_638085568095922939.png&sub_type=thumbnail_preview&type=attachment&width=743&height=588)
URL : https://www.facebook.com/photo/?fbid=2071145259742526&set=gm.5679745985405777&idorvanity=995363477177408 (https://www.facebook.com/photo/?fbid=2071145259742526&set=gm.5679745985405777&idorvanity=995363477177408)
QuoteTony Griffiths
?
Happy new year everyone. Please read the description before messaging. Recently I rebuilt a 1975 hilman avenger. To achieve this I purchased a donor car. The shell was sent to scrap after I got the front off it and now I have a lot of misc parts left over. Including a spare engine in unknown condition. A lot of good parts and some in poor condition. I would like to offer these on for free with the condition that all parts are taken. I?m located in Kamo Whangarei
oh wow no ive just asked to join the group, but would prefer to do what this guy did, and get a donor car
Quote from: JoKer on January 06, 2023, 12:08:04 PM
Did anyone see, or respond to the FREE parts listed on FB over the break?
(https://jaredm-nz.tinytake.com/media/13d131f?filename=1672960015304_TinyTake06-01-2023-12-06-47_638085568095922939.png&sub_type=thumbnail_preview&type=attachment&width=743&height=588)
URL : https://www.facebook.com/photo/?fbid=2071145259742526&set=gm.5679745985405777&idorvanity=995363477177408 (https://www.facebook.com/photo/?fbid=2071145259742526&set=gm.5679745985405777&idorvanity=995363477177408)
I have tried to go into town to get these parts & each time I can't either its flooded or tree slipped across the road so someone else has got them today but I don't really need them was just save them from been thrown out
Olds Cools Auto's in Palmy North have recently listed bits from the Blue Shell posted other day
all expired as I'm late to that party but might be of use to someone here
and kinda handy for a price quide for these things I thought <3
(https://jaredm-nz.tinytake.com/media/14421f3?filename=1680558665195_TinyTake04-04-2023-09-50-54_638161554621555845.png&sub_type=thumbnail_preview&type=attachment&width=799&height=445)
View seller's other listings (https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/gear-boxes/listing/4059132877?member_hash=cadd46d681c1b791a8e9224b00ee4c33d597c6a326929bb2e6&tm=email&et=46&mt=D2763320-CBD5-41AC-AFD4-EB154754D2BA&bof=wTKNCQ09URL%20to%20the%20gearbox%20listing%3Cbr%20/%3E%3Cbr%20/%3E%5Burl=https://www.trademe.co.nz/a/search?member_listing=2716641&bof=wTKNCQ09)
Chrysler Avenger parts https://www.trademe.co.nz/4103671007 (https://www.trademe.co.nz/4103671007)
ASOC parts "NEW"
yeah : members only etc
(https://scontent.fakl2-1.fna.fbcdn.net/v/t39.30808-6/347134250_641159784202947_7707855684340782894_n.jpg?_nc_cat=105&ccb=1-7&_nc_sid=5cd70e&_nc_ohc=2MVtRfD4cwsAX9PWkHk&_nc_ht=scontent.fakl2-1.fna&oh=00_AfAdztsLSXx1fPSNZdKBhm28ye--KufOXmc4CSKUKNe5Mw&oe=648343D6)
QuoteAvenger Sunbeam Owners Club
A few of the ASOC's remanufactured parts that we have in stock.
Still not a member of the original, biggest and best club for the Sunbeam Lotus? www.asoc.co.uk/join (http://www.asoc.co.uk/join)
Part #'s 2 5 and 3 etc are still relevant to Avenger ?
https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/other/listing/4602876835?bof=uEuCMRCn
QuoteHillman/Chrysler Avenger parts
various parts in various conditions as pictured
need gone, so not selling separately. BUYER MUST TAKE IT ALL!
INCLUDES: 2Shells and doors not pictured yet but will add photos In coming days
need gone by end of next week
edit : turns out these might actually be bits of Richards Old Race car!
https://www.facebook.com/share/Lgg6D6BkqDk8mbZ4/?mibextid=kL3p88
Avenger Louvre ?
Quote from: HenryM on May 12, 2024, 11:48:12 PMhttps://www.facebook.com/share/Lgg6D6BkqDk8mbZ4/?mibextid=kL3p88
(https://jaredm-nz.tinytake.com/media/1625c99?filename=1715554324691_TinyTake13-05-2024-10-51-43_638511511216799449.png&sub_type=thumbnail_preview&type=attachment&width=798&height=334)
Avenger Louvre ?
oooh not sure on that aye : how do they know? & no doubt some clever clogs will say "search the part #"
as yeah : says Aunger, the Manufacturer (not Avenger) seller might be assuming things?
will check against the one I know of (in the South Island :P) otherwise PRETTY KEEN
edit : ahh no doesn't look like it to me eh sorry
(https://jaredm-nz.tinytake.com/media/1625c98?filename=1715554265256_TinyTake13-05-2024-10-50-32_638511510612386886.png&sub_type=thumbnail_preview&type=attachment&width=480&height=240)
I'm guessing that a 'coon / Ford part by the Shape (EB Falcon? ish eh
Damian (https://www.trademe.co.nz/a/search?member_listing=5486166&bof=BbIqXbu5) in Tauranga has listed a few parts
https://www.trademe.co.nz/a/motors/car-parts-accessories/chrysler/exterior/listing/5023757969?bof=WffU23zA
(https://jaredm-nz.tinytake.com/media/16e3afc?filename=1731876663570_TinyTake18-11-2024-09-50-46_638674734584878912.png&sub_type=thumbnail_preview&type=attachment&width=800&height=498&&salt=MTAzMTUyMTFfMjQwMDEyNzY)